Marine

From personal fishing boats to commercial cruise ships, RE³ offers a variety of optimization systems. These systems extend the life of your oil while also making sure it stays clean and water free.

Available Units

Conserver® H2

(RECOMMENDED FOR TRUCKS FROM CLASS SA TO CLASS SA, MASS TRANSIT, CONSTRUCTION VEHICLES, AND MARINE ENGINES ALL WITH RESEVOIRS UNDER 20 GALLONS)


The CU2DA is the larger of the commercial units designed for purification of engine lubricating fluids. This unit can purify fluid in equipment that uses between five and twenty gallons. The CU2DA system is designed for direct attachment on class 8 trucks, on and off road construction equipment, marine equipment and mass transit vehicles. The system uses the pressure of the engine oil system to move the oil from the engine through the Conserver® unit and then gravity feed the purified oil back to the engine’s reservoir. The unit will filter out damaging particles and remove water, allowing the equipment to operate more efficiently. This will extend the life efficiency of the engine oil as well as the engine itself. Next Generation will provide the Conserver® H2 and the installation kit for installation to the frame.  A mounting bracket is available as an additional option to purchase.

Specifications

Flow Rate: 13.5 Gallons per Hour   

Unit Capacity: .8 Gallons   

Tank Capacity: N/A   

Dimensions: 18.5" High x 4.5" Wide  x 5.75" Deep  

 Weight: 20 lbs   


Conserver® HI3 Unit

(RECOMMENDED FOR GEAR BOXES, PUMPS, COMPRESSORS, GENERATORS, RESERVOIRS, AND MARINE EQUIPMENT WITH RESERVOIRS UNDER 50 GALLONS.)


This model uses a single HI3 unit for purification of fluid power systems using up to a 50 gallon reservoir. When the environment allows for a unit to be directly attached to the equipment near the fluid reservoir the Model CU3DA is the best solution. The Conserver® system uses the pressure of the equipment’s fluid system to move the fluids from the reservoir to the Conserver® unit and uses gravity to flow the fluid back to the equipment reservoir. Non pressurized systems will require the use of an optional pump to supply the fluid to the Conserver®. With pressure between 5 and 15 psi, a sufficient flow will occur to the Conserver®. The System Control Box supplies the necessary logic and controls to assure that the Conserver® unit performs properly. Multiple micron retention filtration options are available to assist you in achieving your targeted ISO cleanliness code. Moisture level target is to maintain levels below 250 PPM. The customer will provide the mounting bracket, (template included) for installation. Hoses, Pumps and other optional items are available.


Specifications

Flow Rate: 22.75 Gallons per Hour   

Unit Capacity: 1.2 Gallons   

Tank Capacity: N/A   

Dimensions: 23.0" High x 5.5" Wide  x 6.5" Deep   

Power: 120 - 240 VAC   

Weight: 26 lbs   


HI4 Installed on 100 Gallon Gear Box

Conserver® HI4 Unit

(RECOMMENDED FOR GEAR BOXES, PUMPS, COMPRESSORS, GENERATORS, RESERVOIRS, AND MARINE EQUIPMENT WITH RESEVOIRS UNDER 100 GALLONS.)


This model uses a single HI4 unit for purification of fluid power systems using up to a 100 gallon reservoir. When the environment allows for a unit to be directly attached to the equipment near the fluid reservoir the Model CU4DA is the best solution. The Conserver® system uses the pressure of the equipment’s fluid system to move the fluids from the reservoir to the Conserver® unit and uses gravity to flow the fluid back to the equipment reservoir. Non pressurized system will require the use of an optional pump to supply the fluid to the Conserver®. With pressure between 5 and 15 psi, a sufficient flow will occur to the Conserver®. The System Control Box supplies the necessary logic and controls to assure that the Conserver® unit performs properly. Multiple micron retention filtration options are available to assist you in achieving your targeted ISO cleanliness code. Moisture level target is to maintain levels below 250 PPM. The customer will provide the mounting bracket, (template included) for installation. Hoses, Pumps and other optional items are available.

Specifications

Flow Rate: 60.5 Gallons per Hour   

Unit Capacity: 3.2 Gallons   

Tank Capacity: N/A   

Dimensions: 36.0" High x 8.0" Wide x 9.5" Deep 

Power: 120 - 240 VAC   

Weight: 78 lbs.   


Two Conserver® HI4 Units Mounted on a Stationary Skid

(RECOMMENDED FOR COMPRESSORS, GENERATORS, TURBINES, RESERVOIRS, MARINE EQUIPMENT WITH RESEVOIRS UNDER 400 GALLONS.)


This model uses two HI4 units for purification of fluid power systems using up to a 400 gallon reservoir. This system is mounted on its own stand and can be located near the equipment reservoir. For very large reservoirs where a single unit cannot maintain the desired purification stage the Model CU4-2SRRP is the best solution. Pressurized systems require only the included pump for returning fluid from the Conserver® reservoir while non pressurized system will require the use of a second (optional) pump to supply the Conserver® by moving the fluid from the equipment reservoir to the Conserver® unit. The System Control Box supplies the necessary logic and controls to assure that the Conserver® unit performs properly. This configuration is for equipment with larger reservoirs or larger holding tanks. The Conserver® Model CU4-2SRRP uses a reservoir to balance the flow of fluid through the purification process. Multiple micron retention filtration options are available to assist you in achieving your targeted ISO cleanliness code. Moisture level target is to maintain levels below 250 PPM. Hoses, Pumps and other optional items are available.


Specifications

Flow Rate: 121.0 Gallons per Hour   

Unit Capacity: 6.4 Gallons   

Tank Capacity: 18 Gallons   

Dimensions: 64" High x 32" Wide x 42" Deep 

Power: 120 - 240 VAC   

Weight: 280 lbs.